BHFLF - TECTYL 846
- MSDS: BHFLF
- Manufacturer: VALVOLINE OIL COMPANY DIV OF ASHLAND OIL INC
- Product Name: TECTYL 846
- National Stock Number: 8030-00-062-5866
Product Identification
Product ID:TECTYL 846
MSDS Date:03/17/1989
FSC:8030
NIIN:00-062-5866
MSDS Number: BHFLF
Responsible Party
US
Emergency Phone: 606-324-1133
Info Phone: 606-329-3333
Cage: 72527
Contractor
Telephone: 606-357-7206 / 800-274-5263
Cage: 72527
Ingredients
ALIPHATIC PETROLEUM DISTILLATES
CAS: 8052-41-3
Fraction By Weight: 45-50%
OSHA PEL 500 PPM
ACGIH TLV: 100 PPM; 9293
Hazards
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:OVEREXPOSURE TO MATERIAL (OR ITS
COMPONENTS) HAS BEEN SUGGESTED AS A CAUSE OF THE FOLLOWING EFFECTS
IN HUMANS; CENTRAL NERVOUS SYSTEM EFFECTS
Effects of Overexposure:EYE: SEVERE IRR, RED, TEAR, BLURRED VISION.
SKIN: PROLONGED/REPEATED CONTACT, MOD IRRI, DEFAT, DERMA,
BREATHING: NASAL & RESPIRATORY IRRI, CENTRAL NERVOUS SYS EFFECTS,
DIZZ, WEAK, FATIGUE, NAUSEA, HEA DACHE & UNCONS, EVEN DEATH.
SWALLOW: GASTROIN, IRRI, NAUSEA, VOMIT, DIARRHEA. ASPIRATION IN
LUNG CHEM PNEUMONITIS, FATAL
First Aid
First Aid:SKIN: WASH AREA WITH SOAP & WATER. REMOVE CONTAM CLOTHES.
LAUNDER BEFORE RE-USE.EYE: FLUSH WITH LARGE AMTS OF WTR, LIFT LIDS,
GET MED ATTN. SWALLOW: DO NOT INDUCE VOMITING, KEEP PERSON WARM,
QUIET, GE T MED ATTN. ASPIRATION OF MATERIAL INLUNGS DUE TO VOMIT
CAUSE CHEM PNEUMONITIS CAN BE FATAL. BREATH: REMOVE TO FRESH AIR.
IF BREATH DIFF, ADMIN OXYGEN, IF STOPPED GIVE CPR. GET MEDICAL
ATTENTION
Fire Fighting
Flash Point:100 F 37.8 C
Lower Limits:1.0
Extinguishing Media:REGULAR FOAM OR CARBON DIOXIDE OR DRY CHEMICAL
Fire Fighting Procedures:NEVER USE WELD/CUTTING TORCH ON/NEAR DURM
(EVEN EMPTY) PRODUCT (EVEN JUST RESIDUE) CAN IGNITE EXPLOSIVELY.
VAPORS ARE HEAVIER THAN AIR & MAY TRAVEL ALONG GROUND
Unusual Fire/Explosion Hazard:MAY MOVE BY VENT & IGNITE BY HEAT, PILOT
LIGHTS, ETC. AT LOCATION DISTANT FROM MATERIAL HANDLING POINT
Accidental Release
Spill Release Procedures:SML: ABSORB LIQ ON PAPER, VERMICULITE, FLOOR
ABSORB, ETC. & TRANS TO HOOD. LRG: ELIMINATE INGITE SOURCES. WEAR
PROTECTIVE EQUIP, REMOVE PERSONS NOT. STIP SPILL AT SOURCE, DIKE
AREA, PREVENT SPREAD. PU M LIQ-SALVAGE TANK. ABSORB/SHOVEL INTO
CONTAINERS
Handling
Handling and Storage Precautions:KEEP AWAY FROM HEAT & OPEN FLAME.
USE/STORE ONLY W/ADEQUATE VENT. MAINTAIN AMBIENT AIR CONCENT(S)
BELOW PERMISS EXPOSURE LIMITS. AVOID EYE/SKIN CONTAC
Other Precautions:MIN EXPOSURE THROUGH GOOD HYGIENIC PRACTICES. DO OT
TRANS TO UNLABELED CONTAINERDO NOT USE CUT/WELDING TORCH ON THIS
CONTAINER (EVEN EMPTY). FOR INDUSTRIAL USE ONLY. 24 HR EMERGENCY
NO. 1-800-ASHLAND. OBSERVE ALL HAZARD PRECAUTIONS
Exposure Controls
Respiratory Protection:IF EXCEEDED A NIOSH/MSHA APPROVED AIR SUPPLIED
RESPIRATOR IS ADVISED IN ABSENCE OF PROPER ENVIR CONTROL. OSHA REG
ALSO PERMIT NIOSH/MSHA RESPIRATORS (NEG PRESURE TY) UNDER SPECIFIED
COND. ENGINEER/ADM IN CONTR BE IMPLEMENT TO REDUCE EXPOSURE
Ventilation:SUFFIIENT MECH (GEN &/OR LOCAL EXHAUST) VENT TO MAINTAIN
EXPOSURE BELOW TLV(S)
Protective Gloves:IMPERVIOUS GLOVES
Eye Protection:CHEM SPLASH GOGGLES/SAFETY GLASSES OSHA
Other Protective Equipment:TO PREVENT REPEATED/PROLONGED SKIN CONTACT,
WEAR IMPERVIOUS CLOTHING AND BOOTS
Work Hygienic Practices:GOOD PERSONAL HYGIENE PRACTICES
Supplemental Safety and Health
PREVENT RUN-OFF TO SEWERS, STREAMS, OTHER BODIES OF WATER. RUN-OFF
OCCURS, NOTIFY PROPER AUTHORITIES AS REQUIRED, THAT A SPILL HAS
OCCURED. CONTAINERS OF THIS MATERIAL MAY BE HAZARDOUS WHEN EMPTIED.
S INCE EMPTIED CONTAINERS RETAIN PRODUCT RESIDUES, ALL HAZARD
PRECAUTIONS GIVEN IN THIS DATA SHEET MUST BE OBSERVED
Chemical Properties
Boiling Pt:B.P. Text:334.00 F
Vapor Pres:68.00 F
Spec Gravity:60.00 F
Evaporation Rate & Reference:SLOWER THAN ETHER
Appearance and Odor:STATE-LIQUID, FORM-HETER SOLN, AND APPEARANCE-NOT
SPECIFIED
Percent Volatiles by Volume:45-50
Stability
Stability Indicator/Materials to Avoid:YES
NK
Stability Condition to Avoid:AVOID CONTACT WITH; STRONG OXIDIZING
AGENTS
Hazardous Decomposition Products:CARBON DIOXIDE & MONOXIDE, VARIOUS
HYDROCARBONS, SULFUR COMPOUNDS, ETC.
Conditions to Avoid Polymerization:CANNOT OCCUR
Disposal
Waste Disposal Methods:SML: ALLOW VOLATILE PORTION EVAP IN HOOD. ALLOW
VAPORS TO COMPLETE CLEAR HOOD DUCT, DISPOSE MATERIALIN ACCORD
W/APPLICABLE REG. LRG: DESTROY BY LIQ INCIN, CONTAM ABSORBENT
DEPOSITED IN LANDFILL IN ACC ORD WITH LOCAL, STATE & FED REG
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.